Builders
|
|
|
| Barrel, Locking, Rod, Brass, 3/8" | Barrel, Locking, Rod, Brass, 5/16" | Bracket, Free Stand, Knee Lever, MSA |
Brass Rod Locking Barrel Ø1/4" x 5/16" & 3/8" Long | Brass Rod Locking Barrel Ø1/4" x 5/16" & 3/8" Long | Bracket that will allow you to mount 2 knee levers inboard of the rear rail. This bracket may also be positioned anywhere you have room. Fits most all pre-1985 MSA pedal steel guitars. |
$9.00 | $9.00 | $25.81 |
|
|
|
| Bracket, Free Stand, Reversing, MSA | Bracket, Hanger, Pro-Series | Bracket, Stop, Pedal |
Bracket that will allow you to mount a right hand knee lever with a reversing link, inboard of the rear rail. | Cross shaft apron support for Sho-Bud Pro-Series pedal steel guitars. | Pedal stop bracket to fit Sho-Bud early model pedal steel guitars. |
$28.75 (1) | $6.90 | $6.00 |
|
|
|
| Bracket, Support, Bushing, Shaft | Bracket, Support, Shaft, Round | Bushing, Shaft, Cross, Delrin |
Support brackets for hex cross shaft bushings on Sho-Bud pedal steel guitars. | Aluminum angle supports for Ø.3125" (5/16") round and hex cross shafts on Sho-Bud pedal steel guitars.
| Round and Hex cross shaft bushings to fit Sho-Bud pedal steel guitars. |
$5.38 | $5.25 | $5.75 |
|
|
|
| Bushing, Shoulder, Pedal Pull, Delrin | Clip, Spring, Retaining, Pull Rod | Nut, Acorn, #10-32 |
Shouldered Delrin bushings to fit the pedal pull on early model (Pre-1985) MSA pedal steel guitars. |
| Acorn Nut for covering the thread on the shoulder bolt which attaches the RKR to the rear rail on MSA pedal steel guitars. Also used on the pivot screws that attach the knee lever to the shaft bracket. |
$0.50 | $8.00 | $0.49 |
|
|
|
| Nut, Jam, #10-32 | Pull Rod Cut to Fit for ZB's | Pull Rod Nut, #4 |
#10-32 Jam Nut for various applications on pedal steel guitars. | Replacement pull rod for ZB pedal steel guitars. These rods are made from steel and are similar to OEM equipment. This set contains 1 rod assembly which is 27" long O.A.L. and are designed to replace or add any rod length needed. Just measure and... | Pull Rod Nuts to fit smaller diameter pull rods. 3/16" Hex for Ø.109 rods with #4-40 thread. |
$0.16 | $17.95 | $10.00 (3) |
|
|
|
| Pull Rod Set Cut to Fit Ø.109" w/#4-40 Thread | Pull Rod Set Cut to Fit Ø.109" w/#5-40 Thread | Pull Rod Set Cut to Fit Ø.125" w/#5-40 Thread |
Set of 2 pull rods for any pedal steel guitar that use the Ø.109 rod with a cut #4-40 threaded rod end. These are made of Stainless Steel. This set contains 2 rods which are 16" or 32" long and are designed to replace or add any rod length... | Set of 2 pull rods for any pedal steel guitar that use the Ø.109 rod with a rolled #5-40 threaded rod end. These are made of Carbon Steel. This set contains 2 rods which are 16" or 32" long and are designed to replace or add any rod length... | |
$10.50 | $9.28 (1) | $7.50 |
|
|
|
|
| Pull Rod Spoke end for ZB's | Shaft, Cross, D10/D12, MSA | Shaft, Cross, Hex, Pro-Series |
Replacement pull rod end for ZB pedal steel guitars. | Cross Shafts to fit MSA S12 pedal Steels. | 5/16" Hex cross shafts to fit Sho-Bud and Fender pedal steel guitars. |
$3.45 | $9.00 | $3.85 |
|
|
|
| Shaft, Cross, Round, Early Pro-Series | Shaft, Cross, S10, MSA | Shaft, Cross, S12, MSA |
Pedal pull cross shafts for Sho~Bud steel guitars with 2 hole pulls. Shafts include snap ring. | Cross Shafts to fit MSA S10 pedal Steels. | Cross Shafts to fit MSA S12 pedal Steels. |
$9.75 | $8.00 | $8.00 |
|
|
|
|
| Shaft, Cross, SideKick, MSA | Shaft, Cross, SS, S10, MSA | Spring, Return, Finger, MSA |
Cross Shafts to fit MSA SideKick pedal Steels. | Cross Shafts to fit MSA pedal Steels. | Finger Return Spring for Pre-1983 MSA guitars. |
$7.00 | $7.00 | $3.50 |
|
|
|
| Spring, Return, Pedal, MSA | Washer, Nylon, Ø.505 ID, Ø.750 OD, .032 Thick | Ball Joint, Quick Connect |
Pedal Return Spring for Pre-1983 MSA guitars. | Nylon washer for MSA Changers. These washers are used between the finger assemblies. Actual thickness varies between .032-.036". Packages of 11 or 13 washers. | Quick Connect 90° and 180° ball joints. |
$7.00 | $5.50 | $7.50 (3) |
|
|
|
| Bracket, Helper Spring, 10 Hole | Bushing, Shaft, Cross, Delrin | Lever, Knee, Sanded |
Helper Spring Bracket to fit various early models of Sho-Bud pedal steel guitars. | Delrin bushings to fit early model (Pre-1985) MSA pedal steel guitars. | Knee Lever for early model (Pre-1985) MSA pedal steel guitars. |
$4.75 | $7.00 | $25.50 |
|
|
|
| Lever, Knee, Teardrop | Pull Rod Nut, #5 | Finger Assembly - Professional |
Knee lever to fit various early models of Sho-Bud pedal steel guitars. | Pull Rod Nuts, 3/16" Hex in a variety of lengths. | Sho-Bud Finger Assembly for the Professional model.
|
$26.00 (3) | $10.00 (1) | $28.00 |
|
|
|
| Pull, 4 Hole | Pull, 2 Hole | Bracket, Lever, Knee, Shaft |
4 hole Bellcrank (Rod Pull) to fit early model (Pre-1985) MSA pedal steel guitars. | 2 hole Bellcrank (Rod Pull) to fit early model (Pre-1985) MSA pedal steel guitars. | Shaft mount knee lever clamp for early model (Pre-1985) MSA pedal steel guitars. |
$29.50 (1) | $26.50 (1) | $19.50 |
|
|
|
| Bracket, Knee Stop, Small | Stop, Shaft | Lever, Knee, Vertical |
Knee Stop Bracket to fit various models of Sho-Bud pedal steel guitars. | Shaft Stop for 3/8" Shafts | Vertical Knee Lever to fit early model (Pre-1985) MSA pedal steel guitars. |
$10.67 | $9.50 | $19.50 |
|
| |
| Support, Pivot, Lever, Knee, Vertical | Pull, Lever, Knee, Vertical | |
Vertical Knee Lever Support Tower | Vertical Knee Lever Actuating Pull | |
$29.35 | $20.50 | |
